Start with the status shown by the POS and use the least disruptive recovery. Refresh does not erase links; New PIN replaces a pairing attempt; Clear all removes every display link for the current register. Never approve an unknown device or expose customer details in screenshots sent to support.

Before you beginRecord the exact screen, time, expected behavior, and smallest repeatable steps. Remove unnecessary customer and payment data from screenshots.

Step by step

  1. Confirm both devices are using https://pos.getcentri.com and can load it over the network. On the POS, verify the business, location, and register in the context bar. On the display, verify the store and register names shown after connection. A display connected to the wrong register should be disconnected and paired again from the correct register.
  2. If the monitor control is disabled or says Customer display unavailable, open the register session. Pairing codes and display status are resolved against an active session; closing or switching registers changes the operating context.
  3. If the POS says Customer display not connected, choose Installed or Temp and use the current four-digit PIN or QR on the display. The PIN lasts 10 minutes. PIN not found or expired means return to the POS, choose New PIN, and enter only the newest code.
  4. If the display says Waiting for Approval, return to the POS. Confirm the displayed nickname and device ID suffix, then choose Confirm Install or Confirm Join. Check Again on the display only rechecks; it does not replace the required POS approval. Cancel abandons that display-side attempt.
  5. If an installed screen says Customer Display Ready and is waiting for the linked checkout host, confirm the intended POS device has opened the intended register. Retry reloads the display. Use Reset Link only when the installed trust is wrong or damaged, because the device must be paired and approved again afterward.
  6. Open Display Management on the POS. Live means the device checked in recently; Stale means it has not checked in within the current 75-second health window. Read Last seen and distinguish a momentary delay from a device that stopped responding.
  7. For Customer display not responding or Temporary display lost connection, keep the display page open, wake the device, confirm it remains online, and reload the branded /customer-display page. Choose Refresh on the POS to recheck. If the temporary pairing cannot restore, use Disconnect or Reset Pairing on the display, create a New PIN on the POS, and approve the new join.
  8. If the display is connected but says Waiting for your associate to start a sale, begin a new sale on the linked register and add one harmless test item. That waiting screen is correct when there is no active cart or no line items.
  9. If the display shows a cart but stops changing, confirm the header’s activity label is Live rather than an older Last updated state. Make one safe cart change, wait for the live broadcast or the visible-page fallback refresh, and choose Refresh on the POS. Do not repeat or alter a payment to test display synchronization.
  10. If the display shows the wrong cart, stop customer use immediately. Confirm the register context, disconnect the temporary display or reset the incorrect installed link, then pair from the correct register. Do not use Clear all on a different register in an attempt to fix it.
  11. Use Clear all on the POS only after Refresh, reload, and a fresh PIN have failed or when the register’s device trust is known to be wrong. Clear all resets every installed link and disconnects all pending or connected temporary pairings for that register, so every intended display must reconnect.
  12. If the POS reports Unable to reach customer display service or Customer display status unavailable while both devices have working network access, collect the exact status title and message, business, location, register, display mode, device nickname, masked device ID suffix, Last seen value, browser/device type, and time of failure. Do not include the PIN, customer information, full receipt, credentials, or internal service URLs. Send those details through the support path on this help center.

Screen and contract reference

Control or areaWhat it means
Customer display unavailableThe register has no open session, so a connect code cannot be created or managed.
Customer display not connectedOpen register with no approved display link.
PIN not found or expiredThe four-digit code is invalid, replaced, or older than its 10-minute lifetime.
Waiting for ApprovalValid device request pending explicit approval on the POS.
Customer Display ReadyInstalled display is trusted but waiting for its linked POS host and open register.
Connected — live updatesDisplay is paired and listening for the register’s live sale.
Waiting for your associate to start a saleHealthy connection with no active cart items to show.
LiveDisplay or active sale is checking in within its supported freshness window.
StaleDisplay has not checked in within 75 seconds.
Last seenTime since the latest display check-in.
Customer display not respondingInstalled link exists but its display stopped checking in.
Temporary display lost connectionTemporary pairing exists but its browser stopped checking in.
Retry / Check AgainReloads or polls the current display state; does not approve a device or create a new PIN.
RefreshPOS-side status recheck that preserves links.
New PINCreates a fresh 10-minute connection code and replaces the applicable pending pairing.
Reset Pairing / DisconnectClears the temporary display’s local pairing and, when possible, disconnects its active temporary pairing.
Reset LinkRemoves installed trust from that display device.
Clear allDestructive register-level recovery that resets all installed links and disconnects all temporary or pending pairings.
Safe support detailsStatus message, operating context, device nickname and masked ID, last-seen age, browser/device type, and timestamp—never PINs, credentials, customer data, or internal URLs.

Expected result

The intended display reports Live for the correct open register, shows the expected waiting or current-cart state, and receives a controlled cart update without resetting a healthy device on another register or exposing customer information.

Troubleshooting

  • Capture the exact screen, time, expected result, and smallest repeatable steps.
  • Remove unnecessary customer and payment information from screenshots.
  • Include only safe receipt, order, or record references when contacting support.

More guides

Build an itemized payment in MoneyUse Products or Amount & description to build one receipt, attach the customer, and follow the appropriate payment or service-estimate workflow.
Take a one-time payment in Virtual TerminalReview a one-time amount, tax and contact at the correct payment station, use its verified secure checkout, and recover the original receipt after an uncertain result.
Review booking payments, refunds and earned careKeep a booking’s customer payments, unused advances, completed care, cancellation fees and refunds distinct, then read a correctly scoped accrual report.
Configure booking properties and customer pagesSet accommodations, service packages, availability, required intake and payment terms, then review the correctly branded booking page before sharing it.